In this post I will review the process of creating Content Views (CV), Composite Content Views (CCV), publishing each view, and creating lifecycles.
Note that in this post we are working with Red Hat Satellite 6.4, in which there was a major overhaul of the WebUI. You may have noticed that all menus are now situated on in a pane on the left, rather than at the top of each page.
Sync Plans
A sync plan is a constant, scheduled synchronization of updates of a Red Hat Satellite repository and the source repositories. I suggest syncing either daily or weekly in order to minimize the deltas between each sync. When you sync more often, the amount of change between syncs is less and therefore should complete faster than a monthly sync.
Note that this step assumes that you have already setup the correct repositories for RHEL and Red Hat OpenStack. A list of required repositories can be found in the Red Hat OpenStack Director Installation and Usage Guide.
Navigate to Content > Sync Plans
Here we create a daily sync plan for RHEL 7.
We now add RHEL 7 as the product.
Now we need to create a daily sync plan for Red Hat OpenStack.
Note: you might need to create a sync plan for Ceph as well. Ensure all plans sync at the same interval.
Create a Content View
Now we need to create our content views. We will create one for RHEL, and one for OSP. If you are using ceph, you will need to create a content view for it as well.
With the release of Red Hat OpenStack 13, the move to containerized overcloud services is complete. Traditional systemd services such as RabbitMQ, Haproxy, Mariadb, etc, are all now running as containers in the overcloud. This move to containers is meant to provide additional stability, control, and security to the platform. Future upgrades should be easier, and future deploys should be more flexible.
However, the move to containers brings with it a couple of new challenges. Operations.
The average OpenStack administrator no longer restarts services, they restart containers.
They no longer view a rabbit cluster’s status on the controller node, but rather within a container on the controller node. Log locations have changed. Config file locations have changed.
In this post I will document the steps that I am using to create a fully virtualized OSP 10 environment in my lab. The undercloud node is a VM, as well as the overcloud nodes. We will configure libvirt so that ironic has the ability to boot and shutdown the VMs on the underlying hypervisor via Ironic.
Add the stack user on your hypervisor. In this case my hypervisor’s hostname is virt01, however we will refer to it as hypervisor for clarity.
Now attempt to libvirt as stack via a remote session. Here we are just connecting back to the localhost, virt01. In the example below, 10.1.99.112 is the ip of the hypervisor. The undercloud has an ip of 10.1.99.10
[simterm]undercloud# virsh –connect qemu+ssh://stack@10.1.99.112/system list –all
[/simterm]
Now ssh as stack to your undercloud vm
Copy stack’s public key to your hypervisor (virt01 in this case). In the command below you will replace the ip address shown with the ip that your undercloud vm will use to connect to libvirt on the hypervisor
Now we need to create a few Virtual Machines. Specifically I am building an environment with 5 virtual machines to run virtualized Red Hat Openstack 13. My overcloud will consist of 2 computes and three controller nodes
You should end up with the following virtual machines
[simterm]hypervisor# virsh list –all
Id Name State
1 undercloud running
– overcloud-node1 shut off
– overcloud-node2 shut off
– overcloud-node3 shut off
– overcloud-node4 shut off
– overcloud-node5 shut off
[/simterm]
Back on the undercloud we use the command below to grab the provisioning network mac address from each virtual machine running on the hypervisor. We could run this command locally on the hypervisor, but since we need the mac addresses for ironic on the undercloud, we will run it here.
[simterm]undercloud$ for i in {1..5}; do virsh -c qemu+ssh://stack@10.1.99.112/system domiflist overcloud-node$i | awk ‘$3 == “provisioning” {print $5}’; done> /tmp/nodes.txt
[/simterm]
Now we use our temp file above to populate the instackenv.json that we will import into ironic. See gist below
At this point we are ready to import our nodes via Ironic.
Note that I do not claim to be the original author of the steps documented above, rather I wanted to ensure that I could easily consume these steps in the future.
Also, I look forward to experimenting with the vbmc ironic driver and might stop using pxe_ssh altogether.
I have recently purchased 3 Dell servers, and put myself to task to build out a new lab. My old lab was in desperate need of updating as I had long past the time when 48GB of memory per node was sufficient. The cost of memory, old or new was not even closely in line with cheap server grade CPUs that were perfect for lab servers. Today you can buy a used E7540, a low power, 12 core (HT enabled) Xeon for less than $30 (USD) from a reputable retailer. Cram two of these into an 11 gen Dell and you are in business.
So, three new (to me) Dell rackmounts, deployed as virtualization servers, and I want a simple way to view performance stats in a nice clean single pain of glass. I am not in any way shape or form looking to build fancy dashboard and setup any sort of historical monitoring. I just want to know where the performance hot spots are when my environment seems to be running slowly.
I installed Cockpit before on a laptop or two and thought it might foot the bill, especially since you could use one dashboard for multiple nodes.
So here we are going to deploy Cockpit on all three nodes, on each the steps are the same.
The following is the collectd config that I am running on my RHEL 7 kvm hypervisor. This is not meant to be an all inclusive config for collectd, rather I am looking to gather basic performance metrics on my hypervisors and VMs.
Note that I have disabled selinux, as I am running these hypervisors in my lab. Do not do the same in your production environments.
#setenforce 0
I also edited /etc/selinux/config as shown below. Again, this is for non-prod/test envs. Do not disable in production
# This file controls the state of SELinux on the system.
# SELINUX= can take one of these three values:
# enforcing - SELinux security policy is enforced.
# permissive - SELinux prints warnings instead of enforcing.
# disabled - No SELinux policy is loaded.
SELINUX=disabled
# SELINUXTYPE= can take one of three two values:
# targeted - Targeted processes are protected,
# minimum - Modification of targeted policy. Only selected processes are protected.
# mls - Multi Level Security protection.
SELINUXTYPE=targeted
Also note that I have already configured the EPEL repo.. again, not production.